1 in. Long Conduit Speed Nipple 1/2 in. - Zinc Die Cast - 1 in. Long Conduit Speed Nipple Used with Rigid Coupling to Terminate Threaded Conduit to a Knockout, Box or Enclosure, where space is limited within the box.>;
1 in. Long Conduit Speed Nipple 1/2 in. features include:
- Use with Rigid Coupling to Terminate Threaded Conduit to a Knockout, Box or Enclosure, where space is limited within the box
- Use with a Locknut to provide a Short Raceway between Boxes and enclosures
- Die Cast Zinc
- cULus Listed
- Order Qty of 1 = 1 Pieces
Below is more info on our 1 in. Long Conduit Speed Nipple 1/2 in.
Features include:
- Allows In-Slab Ceiling Drops & Floor Mounts in Poured Concrete
- Provides Flush Threaded Conduit Hub for mounting, pulling, & future access to conduit systems
- Design allows In-Slab Conduit System Prefabrication
- Designed to Eliminate Bending of Conduit in Slabs over 4 in. Thick
- Designed for 90; Bends Through Conduit Runs
- cULus Listed
- Concrete Tight
- Order Qty of 1 = 1 Pieces
Features include:
- Used with a locknut to terminate threaded Rigid and IMC conduit to a box or enclosure
- Bushings rounded surface prevents damage to wire insulation during pulling
- Zinc Die Cast
- cULus Listed
- Order Qty of 1 = 1 Piece
Features include:
- Used with a locknut to terminate threaded Rigid and IMC conduit to a box or enclosure
- Lug provides for bonding jumper to a neutral bus bar
- Thermoplastic liner prevents damage to wire insulation
- Set-screw provided with each fitting locks bushing in any desired position
- Resists corrosion, chemicals, and temperature extremes
- Die Cast Zinc
- UL/CSA Listed
- Order Qty of 1 = 1 Piece
Features include:
- Used with bushings to bond threaded Rigid conduit and IMC to boxes, cabinets, or other enclosures where locknut is exposed
- Grounding locknuts for securing threaded conduit or connectors with tapered or straight thread, to a knockout or unthreaded slip hole in a Box or Enclosure
- Grounding Locknut has Integral Ground Screw to Facilitate Grounding to Enclosure
- Galvanized Steel
- cULus Listed
- Order Qty of 1 = 1 Piece
Features include:
- Conduit locknuts for securing threaded conduit or connectors with tapered or straight thread, to a knockout or unthreaded slip hole
- Galvanized Steel
- cULus Listed
- Order Qty of 100 = 100 Pieces
Features include:
- Conduit locknuts for securing threaded conduit or connectors with tapered or straight thread, to a knockout or unthreaded slip hole
- Zinc Die Cast
- UL/CSA Listed
- Order Qty of 100 = 100 Pieces
Features include:
- Reduce the Trade Size of a Tapered Entry on a Conduit Fitting
- Threaded for Rigid and IMC condulets, Hex Shoulder
- Rolled edge protects wire insulation
- Malleable Iron
- Order Qty of 1 = 1 Piece
Features include:
- Used to Join 2 lengths of Threaded Conduit when Neither Can Be Rotated
- Threaded (NPT) for Rigid Conduit and IMC
- Concrete Tight
- cULus Listed
- Order Qty of 1 = 1 Pieces
Features include:
- Connect Thread-less Rigid Conduit to boxes and enclosures
- Malleable Iron
- Concrete Tight
- Male Hub Thread (NPT)
- Zinc Finish
- cULus Listed
- Order Qty of 1 = 1 Pieces
Features include:
- Connect 2 Sections of Thread-less Rigid Conduit
- Malleable Iron
- Concrete Tight
- Zinc Finish
- cULus Listed
- Order Qty of 1 = 1 Pieces
Features include:
- Used as A Speed Union for Economically Joining 2 Threaded Rigid Metal Conduits
- Use where Conduit Runs are Closely Spaced; or Conduit is tight against Wall, Ceiling or other Obstruction
- Use where Conduits cannot be Turned
- A Neoprene Gasket provides a Concrete Tight Seal at the Joint
- Order Qty of 1 = 1 Pieces
Features include:
- Use to reduce the size of the knockout in a steel outlet box or other metal enclosure or cabinet
- Must use one inside the enclosure opening and one on the outside
- Galvanized Steel
- Order Qty of 100 = 100 Pieces
Features include:
- Use with Rigid Coupling to Terminate Threaded Conduit to a Knockout, Box or Enclosure, where space is limited within the box
- Use with a Locknut to provide a Short Raceway between Boxes and enclosures
- Die Cast Zinc
- UL/CSA or cULus Listed
- Order Qty of 1 = 1 Pieces
Features include:
- Use as an Offset Connector between Two Enclosures
- Use To Offset the Axis of Raceways 3/4 in.
- Die Cast Zinc
- UL/CSA Listed
- Order Qty of 1 = 1 Pieces
Features include:
- For Connecting Rigid Conduit or IMC to an Outlet Box in Tight Radius Applications where a Full Size Elbow Will Not Fit
- Zinc Die Cast
- NPT Thread
- cULus Listed
- Order Qty of 1 = 1 Pieces
Features include:
- To secure threaded Rigid Service Entrance conduit & IMC to box or enclosure in a WaterTight Application
- Assembled with 221;F (105C) rated flame retardant Lexan throat insulator and BUNA-N sealing ring that completely encircles knockout to prevent contaminants from entering enclosure
- For use in Wet Locations
- cULus Listed
- Order Qty of 1 = 1 Piece
Features include:
- For Connecting Threaded Rigid or IMC Conduit to Box or Enclosures to Form 90" bend
- Removable Cover allows easy access to facilitate wire pulling
- Furnished with Neoprene Gasket and Cover
- Rain Tight
- UL/CSA Listed
- Order Qty of 1 = 1 Pieces
Features include:
- For use as a Wire Pulling Elbow to Facilitate Wire Pulling on a Sharp Bend in run of Threaded Rigid or IMC Conduit
- Removable Cover allows easy access to facilitate wire pulling
- Furnished with Neoprene Gasket and Cover
- Rain Tight
- UL/CSA Listed
- Order Qty of 1 = 1 Pieces
Features include:
- Sealing locknuts provide a rain-tight seal when securing threaded conduit or connectors with tapered or straight thread, to a knockout or unthreaded slip hole of a box or enclosure
- Sealing Locknut has a Integral Gasket
- Galvanized Steel
- Order Qty of 1 = 1 Piece
Features include:
- Reduce the Trade Size of a Tapered Entry on a Conduit Fitting
- Threaded for Rigid and IMC condulets, Hex Shoulder
- Rolled edge protects wire insulation
- Order Qty of 1 = 1 Piece
Features include:
- Allows In-Slab Ceiling Drops & Floor Mounts in Poured Concrete
- Provides Flush Threaded Conduit Hub for mounting, pulling, & future access to conduit systems
- Design allows In-Slab Conduit System Prefabrication
- Designed for Straight Through Conduit Runs and Mounting of Floor boxes in slabs over 6 in. thick
- Concrete Tight
- Order Qty of 1 = 1 Pieces
Features include:
- Threaded plastic inserts for RIGID or IMC conduit
- Use to Protect Conductors in Rigid or IMC Conduit from Abrasion/Damage during Pull
- Thermoplastic material—heat, impact and torque resistance
- Strong reinforcing ribs & rim around bottom
- Flame retardant Polypropylene (Rated to 221;F, 105C)
- 1/2 in wide
- Threaded plastic inserts are UL/CSA Listed
- Dimension Measurements = Inches
- UL/CSA Listed
- Order Qty of 100 = 1 Bag of 100